Email: info@industrial-mall.com

Shipping To All Over Saudi Arabia

iconHotline: 

Email: info@industrial-mall.com

Shipping To All Over Saudi Arabia

iconHotline: 

Email: info@industrial-mall.com

Shipping To All Over Saudi Arabia

iconHotline: 

Product Details

Permatex Ultra Black Maximum Oil Resistance RTV Silicone Gasket Maker Tds

Permatex Ultra Black Maximum Oil Resistance RTV Silicone Gasket Maker

OEM specified. For dealership warranty requirements, Ultra Black® ensures extended drivetrain warranty compliance. Fast-curing formula. Sensor-safe, low odor, noncorrosive. Meets performance specs of OE silicone gaskets. Retains high flexibility, oil resistant properties through use of a patented adhesion system. Temperature range -65°F to 500°F (-54°C to 260°C) intermittent; resists auto and shop fluids and vibration.

Automobile

Suggested Applications: Valve covers, oil pans, intake manifold end seals, timing covers, differential covers

Marine

Suggested Applications: Valve covers, oil pans, intake manifold end seals, timing covers, water pumps, thermostat housings

Compare

Share this product

Description

PRODUCT DESCRIPTION
Permatex Ultra Black Gasket Maker is a single component,
room temperature, vulcanizing, gasketing compound designed
to provide reliable “formed-in-place” gaskets for mechanical
assemblies. This material cures on exposure to moisture in
the air to form a tough, flexible, silicone rubber gasket. The
product resists aging, weathering and thermal cycling without
hardening, shrinking or cracking. Designed to provide
increased oil resistance and complies with extended warranty
requirements. OEM Specified.
PRODUCT BENEFITS
• Improved oil resistance
• Sensor safe, non-corrosive
• Good adhesion and flexibility
• Replaces most cut gaskets
• Can be used as a gasket maker or dressing
• Non-flammable, Non-toxic
• Low odor
TYPICAL APPLICATIONS
• Oil pans
• Transmission pans
• Valve covers
• Valves and guides
• Timing gear covers
• Differential covers
DIRECTIONS FOR USE
For assembly as a form-in-place gasket
1. Remove all previous material from mating surfaces.
Permatex® Gasket Remover is recommended for most
materials, not for plastics or painted surfaces.
2. For best results, clean and dry all surfaces with a
residue-free solvent, such as Permatex® Brake and
Parts Cleaner
3. Cut nozzle to desired bead size, 1/16” to 1/4” in
diameter. A 1/8” bead is usually sufficient for most
applications.
4. Remove cap, puncture tube or cartridge seal and attach
extension nozzle.
5. Apply a continuous and even bead of silicone to one
surface, first tracing the internal areas of the gasket
configuration, then all surrounding bolt holes as shown
below:

Assemble parts immediately while silicone is still wet.
7. Finger tighten flange only until material begins to seep
out the sides of the flange.
8. Allow to set for at least two hours and re-torque at least
one quarter to one half turn.
9. For best results, allow to cure overnight.
For assembly as a gasket dressing
1. Repeat steps 1 through 4 as in previous section.
2. Apply a thin film of silicone to one surface to be sealed.
3. Place the pre-cut gasket onto silicone film.
4. Apply a second thin film to pre-cut gasket surface.
5. Remove any excess and assemble parts immediately.
Note: Product is not recommended for use as a cylinder
head gasket or head gasket sealant.
Instructions for PowerBead
1. Clean and dry all flange surfaces to be sealed.
2. Remove black cap from top of extension nozzle.
3. Turn nozzle extension one complete turn (360)
counterclockwise.
4. Depress finger trigger and apply a continuous 1/16 inch
to 1/8 inch PowerBead to one surface.
5. Assemble parts immediately while silicone is still wet.
6. Finger tighten flange only until material begins to seep
out the sides of the flange.
7. Allow to set for at least two hours and re-torque at least
one quarter to one half turn.
8. For best results, allow to cure overnight.
9. To close, turn extension nozzle clockwise until tight
(about one full turn). Wipe off excess material from
nozzle and replace black cap.
Technical Data Sheet Ultra Black Gasket Maker
Permatex, Ultra Black, PowerBead and Fast Orange are trademarks of Illinois Tool Works, Inc. © Copyright 2019. ITW Permatex, Inc. All rights
reserved
Storage of Unused Product
1. Create a “Silicone Plug” by allowing excess material to
extend beyond the extension nozzle or aerosol tip to
cure, sealing and protecting the remaining product from
moisture. For reuse, simply remove the cured product
from the tip.
2. For PowerBead dispensers, you may store remaining
product using either the above “silicone plug” method or
using the included plastic cap.
For Cleanup
1. Remove uncured product from parts and hand-tools with
Permatex Fast Orange Wipes or Fast Orange® Hand
Cleaners. If skinned over, break film with a dry cloth to
remove as much as possible. Remove the remaining
material with Permatex Gasket Remover.
2. Clean hands with a dry cloth or Permatex Fast
Orange Hand Cleaner.

GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials

TECHNICAL DOCUMENTS
Permatex Ultra Black Maximum Oil Resistance RTV Silicone Gasket Maker Tds

Reviews

There are no reviews yet.

Be the first to review “Permatex Ultra Black Maximum Oil Resistance RTV Silicone Gasket Maker”

Your email address will not be published. Required fields are marked *