Email: info@industrial-mall.com

Shipping To All Over Saudi Arabia

iconHotline: 

Email: info@industrial-mall.com

Shipping To All Over Saudi Arabia

iconHotline: 

Email: info@industrial-mall.com

Shipping To All Over Saudi Arabia

iconHotline: 

Product Details

Permatex Medium Strength Threadlocker BLUE

Permatex Medium Strength Threadlocker BLUE

OEM specified. All-purpose, medium strength threadlocker. Ideal for all nut and bolt applications 1/4″ to 3/4″ (6mm to 20mm). Eliminates need for stocking expensive lock nuts and lock washers. Locks and seals while preventing parts loosening due to vibration. Protects threads from corrosion. Removable with hand tools for easy disassembly. Conforms to ASTM D 5363 AN0321 (Mil-S-46163A, Type II, Grade N).

Automobile

Suggested Applications: Valve cover bolts, water pump bolts, oil pan bolts, drive shaft bolts, rocker arm adjustment nuts, carburetor studs

Motorcycle

Suggested Applications: Handlebar brackets, mirror fixtures, shock bolts, rear fender nuts, small fastener nuts

Heavy Duty

Suggested Applications: Case cover bolts, axle housing bolts, oil seal retainer bolts, axle shaft flange bolts, differential drain plugs, fuel tank fasteners, lug nuts, windshield wiper nuts, gear shift knobs, door hardware, running light screws, horning mounting

Marine

Suggested Applications: Valve cover bolts, water pump bolts, oil pan bolts, drive shaft bolts,
rocker arm adjustment nuts, carburetor studs

Compare

Share this product

Description

PRODUCT DESCRIPTION
PERMATEX Medium Strength Threadlocker BLUE is a
medium strength anaerobic threadlocking material, which
cures between engaged threads to form a unitized assembly
that resists virtually all leakage, shock and vibration. The
product is a single component, anaerobic liquid that cures
when confined in the absence of air between close fitting
metal surfaces. Ideal for all 1/4 inch to 3/4 inch diameter nut
and bolt assemblies. Excellent chemical resistance with a
temperature resistance range of -54C to +149C (-65F to
+300F). Easily removable with hand tools for servicing
requirements. OEM Specified. NSF White Book registered.
PRODUCT BENEFITS
Improved Reliability
Eliminates vibration issues
Seals against leakage
Prevents rusting of threads
Cures without cracking or shrinking
Can be adjusted or disassembled
Easy Application
No mixing
No curing outside of joint
Thixotropic: resists dripping from threads during assembly
No torque compensation required during assembly
TYPICAL APPLICATIONS
Prevents loosening and leakage of threaded fasteners.
Particularly suitable for applications such as:
Belt tensioner bolts
Pulley bolts
Cup and core plugs
Fan hub bolts
Visor mount bolts
Starter mounting bolts
Alternator Mounting Bolts
Intake Manifold Bolts
Valve Cover Bolts
Vacuum Adjustment Screws
Oil Pan Bolts
Axle Cover Screws
Drive Shaft Bolts
Disc Brake Caliper Bolts
Gearshift Knobs
DIRECTIONS FOR USE
For assembly
1. Clean all threads (Bolt and Hole) with a cleaning solvent
such as Permatex Brake and Parts Cleaner and allow to
dry.
2. Determine if the threads to be bonded are Active or
Inactive Metals (Ref: Cure Speed vs. Substrate on the
second page). If material is an Inactive Metal, spray all
threads with Permatex Surface Prep and allow 30 seconds
to dry . Priming is not required if the material is an Active
Metal. If unknown, it is always best to use the primer.
3. Shake the product thoroughly before use.
4. To prevent the product from clogging in the nozzle, do not
allow the tip to touch metal surfaces during application.
5. For Thru Holes, apply several drops of product onto the
bolt at the nut engagement area.
For Blind Holes, apply several drops down the female
threads into the bottom of the hole. As threads are
engaged, compressed air forces the product upwards into
the threads.
6. Assemble and tighten as usual. When tightening to
established torque values, torque compensation is not
required.
For Cleanup
1. Residual liquid films and/or fillets outside the joint are
readily soluble in Permatex Brake and Parts Cleaner.

Cured product can be removed with a combination of
soaking in Permatex Gasket Remover and mechanical
abrasion such as a wire brush.
For Disassembly
1. Remove with standard hand tools.
2. In the rare instance where hand tools do not work, because
of excessive engagement length, apply localized heat to nut
or bolt to approximately 232C (450F). Disassemble while
hot.
For Reassembly
1. Remove loose product from nut and bolt.
2. Apply primer to all threads, regardless of metal type.
3. Assemble and tighten as usual.

TECHNICAL DOCUMENTS
Permatex Medium Strength Threadlocker BLUE Tds

Reviews

There are no reviews yet.

Be the first to review “Permatex Medium Strength Threadlocker BLUE”

Your email address will not be published. Required fields are marked *