Email: info@industrial-mall.com

Shipping To All Over Saudi Arabia

iconHotline: 

Email: info@industrial-mall.com

Shipping To All Over Saudi Arabia

iconHotline: 

Email: info@industrial-mall.com

Shipping To All Over Saudi Arabia

iconHotline: 

Product Details

Permatex High Strength Threadlocker RED Gel

Permatex High Strength Threadlocker RED Gel

OEM specified. Gel formula provides “liquid-reliability” without drips, globs, mess or waste. Available in four convenient sizes, the 10G GEL TWIST pin-point applicator, the 5G GEL SQUEEZE applicator, the Professional Size 35G GEL TUBE, or the single-use pouch puts the Threadlocker right where you want it…on the part! High strength threadlocker for heavy-duty applications 3/8 inch to 1 inch (10mm to 25mm). Especially well-suited for permanently locking studs and press fits. Adds 3,000 PSI holding power on slip and press fit assemblies. Replaces set screws and snap rings. Locks against vibration loosening. May require heat or special tools for removal. Conforms to ASTM D5363 AN0221 (Mil-S-46163A, Type I, Grade K).

Automobile
Suggested Applications: Cylinder block and rocker arm studs, ring gear bolts, frame bolts, shock absorber bolts; also ideal for vertical applications

Heavy Duty
Suggested Applications: Cap screws and mounting studs on differentials

Compare

Share this product

Description

PRODUCT DESCRIPTION
PERMATEX High Strength Threadlocker RED Gel is a high
strength anaerobic threadlocking gel conveniently packaged in
a new Gel Twist or Gel Squeeze applicator. The product,
like its liquid counterpart, is a single component, anaerobic gel
that cures when confined in the absence of air between close
fitting metal surfaces, ideal for all 3/8 inch to 1 inch (10mm to
25mm) and greater diameter threaded assemblies. Excellent
chemical resistance and temperature resistance range of -65F
to +300F (-54C to +149C). The assembly may require the
use of heat to remove bolts. NSF Nonfood Components
Program Listed (P1) (135870).
PRODUCT BENEFITS
Improved Reliability
• Eliminates vibration issues
• Seals against leakage
• Prevents rusting of threads
• Designed for use on vertical or hard-to-reach applications
• Cures without cracking or shrinking
• Adjusts or disassembles with hand tools
Easy Application
• No mess Gel Twist or Gel Squeeze applicator
• Gel-type product does not drip when applied
• Single component
• No curing outside of joint
• Thixotropic: resists dripping from threads during assembly
• No torque compensation required during assembly
TYPICAL APPLICATIONS
Prevents loosening and leakage of threaded fasteners.
Particularly suitable for applications such as:
• Transmission shaft bolts
• Cylinder block
• Rocker arm studs
• Ring gear bolts
• Fan hub bolts
• Shock absorber bolts
• Frame brackets
• Frame bolts
• Hydraulic press studs
• Suspension fasteners
• Large studs
• Heavy equipment bolts
• Gear bolts
• Railroad assemblies
• Construction equipment
DIRECTIONS FOR USE
For assembly
1. Clean all threads (bolt and hole) with a cleaning solvent such
as Permatex Brake and Parts Cleaner and allow to dry.
2. Remove the translucent protective cap by pulling off at an
angle.
3. For Gel Twist turn the dial on the bottom of the container
until 1/8” to 1/4″ (3mm to 6mm) of material protrudes from the
top of the application tip. Note: First time use may require 4
to 5 full turns of the dial before material appears in the tip.
For Gel Squeeze, remove cap and squeeze 1/8” to 1/4″
(3mm to 6mm) of material beyond tip.
4. Apply threadlocker to the engagement area of the male fitting
(usually the leading 5 to 6 threads).
5. Assemble parts and tighten to recommended torque.
6. If unused gel contacts metal threads, do not retract
threadlocker back into the tube. Wipe off with a clean towel.
7. Replace protective cap.
For Cleanup
1. Residual liquid films and/or fillets outside the joint are readily
soluble in Permatex Brake and Parts Cleaner.
2. Cured product can be removed with a combination of soaking
in Permatex Gasket Remover and mechanical abrasion
such as a wire brush.
For Disassembly
1. Apply localized heat to nut or bolt to approximately 450F
(232C). Disassemble while hot.
For Reassembly
1. Remove loose product from nut and bolt following cleanup
procedure above.
2. Apply Surface Prep activator to all threads, regardless of
metal type and allow to dry.
3. Apply threadlocker gel as above.
4. Assemble and tighten as usual.

TECHNICAL DOCUMENTS
Permatex High Strength Threadlocker RED Gel Tds

Reviews

There are no reviews yet.

Be the first to review “Permatex High Strength Threadlocker RED Gel”

Your email address will not be published. Required fields are marked *